User Manual DW850 VoIP Phone All rights reserved. This document is supplied by Dreamwizor HK Co.
- 10 - IP with PPPoE. Setting Static IP mode(static ADSL/Cable,or none PPPoE / DHCP network) 1. Prepare the network’s p
- 11 - displays“3 Network” 3. Press Soft2 (Enter) to show “1 Net Mode”. After pressing Soft(Enter) and Soft2(Edit),using
- 12 - 3. DW850’s basic operation 3.1. Answer calls DW850 will ring to indicate you when there is call incoming ,below i
- 13 - If there are many persons records stored in the directory, you can use to search the person which you want to
- 14 - z Attended Transfer During talk, press and input the number that you want to transfer to and press Soft2 (Send
- 15 - or press Soft2 (Detail) to check the details of this record, then press Soft2 (Dial) again to change the current
- 16 - use BLF feature. When this configuration enable, the phone will subscribe the status of pointed phone each 60s: L
- 17 - key to check the sender’s number and message content, next, press Soft2(Reply)key and input message content, fina
- 18 - *1* means appointed prefix code. After making the above configuration, C can dial *1* plus B’phone number to pi
- 19 - 4. Web configuration 4.1. Introduction of configuration 4.1.1. Ways to configure DW850 has three different ways t
- 2 - Safety Notices Please read the following safety notices before installing or using this phone. They are cruci
- 20 - 4.3.1. BASIC 4.3.1.1. Status Status Field name Explanation Network Shows the configuration information on WAN
- 21 - Please select the proper network mode according to the network condition. FV6030 provide three different network
- 22 - Display detailed information that you manual config. Choose DHCP MODE,click【NEXT】can config SIP(default SIP1)simp
- 23 - MMI SET Field name explanation Language Set Set the language of phone, English is default. Greeting Message
- 24 - Active IP The current IP address of the phone. Current Netmask The current Netmask address. MAC Address The cu
- 25 - Notice: 1)Click “Apply” button after finished your setting, IP Phone will save the setting automatically and new
- 26 - In chart 1, there is a layer 2 switch without setting VLAN. Any broadcast frame will be transmitted to the oth
- 27 - QoS ConfigurationField name explanation VLAN Enable Before select it to enable VLAN, you need enable Bridge m
- 28 - 4) Startup VLAN, if set Voice/Data VLAN differentiated as data untaged, then the packet of the signal/voice will
- 29 - 4.3.2.5. DHCP SERVER DHCP SERVER Field name explanation DHCP Leased Table IP-MAC mapping table. If the LAN po
- 3 - Table of Content 1. Introducing DW850 VoIP Phone ...
- 30 - Select name of lease table, click the Delete button will delete the selected lease table from DHCP lease table.
- 31 - Server Set SNTP Server IP address. Time Zone Select the Time zone according to your location. Time Out Set t
- 32 - SIP Config Field name explanation Choose line to set info about SIP, there are 5 lines to choose. You can swit
- 33 - Server Address Input your SIP server address. Server Port Set your SIP server port. Account Name Input your SI
- 34 - Enable PRACK Enable or disable SIP PRACK function, suggest use the default config. Long Contact Set more paramet
- 35 - patckets sent from server, phone will use the source IP address, not the address in via field. Enable GRUU Set t
- 36 - Refresh Time Set expire time of IAX2 server register, you can set it between 60 and 3600 seconds. Enable Registe
- 37 - STUN Server Port Set your SIP STUN Server Port STUN Effect Time Set STUN Effective Time. If NAT server finds th
- 38 - DIAL PEER Field name explanation Phone number There are two types of matching conditions: one is full match
- 39 - 4) Rep: It means that phone will replace the number with length and number appointed. You can refer to the follow
- 4 - 4.3.4. Phone ...
- 40 - This setting will realize speed dial function, after you dialing the numeric key “2”, the number after all will
- 41 - DSP Configuration Field name explanation First Codec The fist preferential DSP codec: G.711A/u, G.722, G.723,
- 42 - Call Service Field name explanation Hotline Specify Hotline number. If you set the number, you can not dial a
- 43 - Record beyond its set value, the phone will remind the caller to record. Incoming Record Playing Select it or no
- 44 - send the prefix and external number totaly to ther server. for example, there is a rule 9,xxxxxxxx in the digital
- 45 - Cause 99 to be dialed after 4 seconds. Cause any number started with 9911 to be dialed 4 seconds after dialing ce
- 46 - Function Key Field name explanation Contrast Set contrast of screen Luminance Set luminance of screen M
- 47 - F_CFWD,or F_CALLERS in the corresponding right table. For example: 4.3.5. Maintenance 4.3.5.1. Auto Provisio
- 48 - Syslog server receives the messages from clients, and classifies them based on priority and type. Then these mess
- 49 - Config Setting Field name explanation Save Config you can save all changes of configurations. Click the Save
- 5 - 1. Introducing DW850 VoIP Phone 1.1. Thank you for your purchasing DW850Thank you for your purchasing DW850, DW8
- 50 - Update Field name explanation Web Update Click the browse button, find out the config file saved before or prov
- 51 - Account Configuration Field name explanation Keyboard Password Set the password for entering the setting menu
- 52 - If you modified some configurations which need the phone’s reboot to be effective, you need click the Reboot, th
- 53 - Notice: Do not set your visiting IP outside the MMI filter range, otherwise, you can not logon through the web.
- 54 - In_access enable Select it to Enable in_ access rule out_access enable Select it to Enable out_ access rule Input
- 55 - DMZ config: In order to make some intranet equipments support better service for extranet, and make internal net
- 56 - NAT Configuration Field name explanation IPSec ALG It is an encryption technology. Select it to enable IPSec A
- 57 - Outside Port Set the WAN port of the NAT mapping Notice: After finish setting, click the Add button to add new m
- 58 - VPN Configuration Field name explanation VPN IP Shows the current VPN IP address Select UDP Tunnel (VPN Tunne
- 59 - Click Logout,and you will exit web page. If you want to enter it next time, you need input user name and passwor
- 6 - Key Key name Function Description menu In idle state,press the MENU key to call up the menu. Up/down of navi
- 61 - 5. Appendix 5.1. Specification 5.1.1. Hardware Item DW850Adapter (Input/Output) Input: 100-240V Output: 5V 1A or
- 62 - z Support path, gruu z Support SRTP z Support SIP Privacy 5.1.3. Network features z WAN/LAN: support bridge
- 7 - more details). In the idle mode, press this key LCD will show ”call forward”, wait this indication disappear, then
- 8 - 2. Initial connecting and Setting 2.1. connect the phone Step 1: Connect the IP Phone to the corporate IP telephon
- 9 - section “Initial setting” to set your network online mode. If your VoIP phone registers into corporate IP telephon
Comments to this Manuals